QUOTE (Aaron @ Jun 23 2008, 08:33 PM)

Most of the damage from a real-life EMP comes from circuits that are not able to handle that much energy going through them. Transistors and things that either act like them (like vacuum tubes) or are made of a gazillion of them (like integrated circuits) use very little energy, so when a LOT goes through them, well, pop.
There are also waveguides to consider. A waveguide is used to ... well, it's used to guide waves. It can amplify signals of certain wavelengths, boosting the signal of a transmission (incoming or outgoing, but we're talking incoming, here). It's used in radios, radar, and basically stuff with an antenna. If you take a high energy wave and boost it, well, that's a lot of power in one place, so it can also be susceptible to EMP.
Most of the damage to electronics in an EMP is to small circuits and waveguides. Obviously, technomancers don't have transistors. They might have waveguides, though; it depends on how they create and receive wireless signals.
BOY!!! do you have waveguides WRONG!!!!. Waveguides amplify nothing, it is merely a transmission method/medium. Microwave amplifiers are Klystrons, Magnetrons, and Traveling Wave Tubes aka TWATS.
KlystronMagnetronTraveling Wave TubeWaveguide WikiQUOTE
Electromagnetic waveguides
Main articles: Waveguide (electromagnetism) and transmission line
Waveguides can be constructed to carry waves over a wide portion of the electromagnetic spectrum, but are especially useful in the microwave and optical frequency ranges. Depending on the frequency, they can be constructed from either conductive or dielectric materials. Waveguides are used for transferring both power and communication signals.
Optical waveguides
Main article: Waveguide (optics)
Waveguides used at optical frequencies are typically dielectric waveguides, structures in which a dielectric material with high permittivity, and thus high index of refraction, is surrounded by a material with lower permittivity. The structure guides optical waves by total internal reflection. The most common optical waveguide is optical fiber.
Other types of optical waveguide are also used, including photonic-crystal fiber, which guides waves by any of several distinct mechanisms. Guides in the form of a hollow tube with a highly reflective inner surface have also been used as light pipes for illumination applications. The inner surfaces may be polished metal, or may be covered with a multilayer film that guides light by Bragg reflection (this is a special case of a photonic-crystal fiber). One can also use small prisms around the pipe which reflect light via total internal reflection [1]—such confinement is necessarily imperfect, however, since total internal reflection can never truly guide light within a lower-index core (in the prism case, some light leaks out at the prism corners).
Acoustic waveguides
Main article: Waveguide (acoustics)
An acoustic waveguide is a physical structure for guiding sound waves. A duct for sound propagation also behaves like a transmission line. The duct contains some medium, such as air, that supports sound propagation.
As quoted above fiber optic is a "waveguide". Yes a "Waveguide" can have booster/minor amps/repeaters but not in the waveguide.
Waveguides are not the "working part" of an antenna array, yes they can carry the signals.
Boosting Microwaves is a entirely different method/manner than fiber optic.
Again Aaron let me implant wires into your brain, let say cerebral cortex, and then run you into a MRI.

Lets see how many volts your cerebral cortex's brain cells can take.
Again the TMA (TechnoMancer Antenna) is used to gathering microvolts of signal, putting 100 of volts of signal across a TMA, results in the TM getting a "Signal" of magnitudes greater than his TMA can deal with. Meaning his CNS takes a shock to say the least. Since unlike most SR4 devices a TM has no fuse or circuit breaker to stop the flow of excessive electrons.
Also most microwave class waveguides are not affected by EMP due in part to the copper interior sheathing, conducts away the charge to some other component in the chain. The BaseBall switches will not be affected, the microwave amps could be affected. The active and or discrete components in the antenna array can also be affected. Fiber optic waveguides are not affected either due to be optical.
Also here a link to the various sizes of waveguides used in radio frequency/microwaves.
Rectangular WaveguidesWMS